Error 2360 overheating
7 years 8 months ago #29531281
by vit
Error 2360 overheating was created by vit
the controller indicates an error overheating, there is no movement of motors.
I shot the video.
what can be done?
firmware updated.
sorry for my bad English.
sometimes it's better demonstrate
www.youtube.com/watch?v=usOXQtugfz0&feature=youtu.be
I shot the video.
what can be done?
firmware updated.
sorry for my bad English.
sometimes it's better demonstrate
www.youtube.com/watch?v=usOXQtugfz0&feature=youtu.be
Please Log in or Create an account to join the conversation.
7 years 8 months ago #29531282
by TechSupport
Replied by TechSupport on topic Error 2360 overheating
That's not overheat. The roborun displays you have undervoltage, which is why the motors won't run.
That means either the voltage you have placed at the vmot is less than the specified if you changed that parameter, or you have placed the voltage at the power control yellow and black wire instead of the red and black wires.
That means either the voltage you have placed at the vmot is less than the specified if you changed that parameter, or you have placed the voltage at the power control yellow and black wire instead of the red and black wires.
Please Log in or Create an account to join the conversation.
7 years 8 months ago #29531283
by vit
Replied by vit on topic Error 2360 overheating
Thanks for the quick response
my battery 48V
I have to point those values?
over voltage 50
under voltage 44
my battery 48V
I have to point those values?
over voltage 50
under voltage 44
Please Log in or Create an account to join the conversation.
7 years 8 months ago #29531284
by TechSupport
Replied by TechSupport on topic Error 2360 overheating
These don't really need to be set unless you are using them for a specific purpose.
If you put the overvoltage to the max rating of the controller and the undervoltage to something lower, then you shouldn't have these errors come up.
If you put the overvoltage to the max rating of the controller and the undervoltage to something lower, then you shouldn't have these errors come up.
Please Log in or Create an account to join the conversation.
7 years 8 months ago #29531285
by vit
Replied by vit on topic Error 2360 overheating
volt
Please Log in or Create an account to join the conversation.
7 years 8 months ago - 7 years 8 months ago #29531286
by vit
Replied by vit on topic Error 2360 overheating
I did reset the controller.
Does not help
I turned off the engines, only connect the power and black-yellow wire to enable the controller.
Does not help
I turned off the engines, only connect the power and black-yellow wire to enable the controller.
Please Log in or Create an account to join the conversation.
7 years 8 months ago #29531287
by TechSupport
Replied by TechSupport on topic Error 2360 overheating
The undervoltage is because you have it connected at the yellow and black wires. That is the power control logic side only. The vmot big red and black wires are where you need to connect power to drive the motors.
Please Log in or Create an account to join the conversation.
7 years 8 months ago #29531288
by vit
Replied by vit on topic Error 2360 overheating
Please Log in or Create an account to join the conversation.
7 years 8 months ago #29531289
by TechSupport
Replied by TechSupport on topic Error 2360 overheating
The status light blink is normal.
Please Log in or Create an account to join the conversation.
7 years 8 months ago #29531290
by vit
Replied by vit on topic Error 2360 overheating
LED indicates overheating
Please Log in or Create an account to join the conversation.
Moderators: tonysantoni
Time to create page: 0.098 seconds
