SDC2160S Pulse Width Input
- RickBrooks
- Topic Author
- Offline
Less
More
- Posts: 9
- Thank you received: 1
5 years 9 months ago #29532198
by RickBrooks
SDC2160S Pulse Width Input was created by RickBrooks
I have a new SDC2160S motor control that doesn't respond to Pulse Width commands. The status LED never indicates RC Pulse Mode when a Pulse signal is sent to RCRadio 1 on Pin 4.
The Command Priorities are set to: 1 Pulse Width, 2 Serial; and Pulse Inputs, Pin 1 is set to Capture Type Pulse Width and Input Use Motor control.
The Firmware is Roboteq V1.6SDC2XXX04/14/2016. I have tries updating the firmware to SDC21XXS Firmware Update v16 - 041416 without improvement.
What can I try to fix the problem?
The Command Priorities are set to: 1 Pulse Width, 2 Serial; and Pulse Inputs, Pin 1 is set to Capture Type Pulse Width and Input Use Motor control.
The Firmware is Roboteq V1.6SDC2XXX04/14/2016. I have tries updating the firmware to SDC21XXS Firmware Update v16 - 041416 without improvement.
What can I try to fix the problem?
Please Log in or Create an account to join the conversation.
5 years 9 months ago #29532203
by blake
Replied by blake on topic SDC2160S Pulse Width Input
Hello,
Please try loading the attached firmware to your controller and let us know your feedback, it should fix the problem. Thanks
Please try loading the attached firmware to your controller and let us know your feedback, it should fix the problem. Thanks
Please Log in or Create an account to join the conversation.
- RickBrooks
- Topic Author
- Offline
Less
More
- Posts: 9
- Thank you received: 1
5 years 9 months ago #29532204
by RickBrooks
Replied by RickBrooks on topic SDC2160S Pulse Width Input
I did the update and the status LED indicates Pulse Mode and Roborun+ does show the Pulse Width signals appearing on the pins.
The firmware appears to be for Dial Channel operation and I wanted Single Channel operation with the SDC2160S.
Thanks
Rick
The firmware appears to be for Dial Channel operation and I wanted Single Channel operation with the SDC2160S.
Thanks
Rick
Please Log in or Create an account to join the conversation.
- RickBrooks
- Topic Author
- Offline
Less
More
- Posts: 9
- Thank you received: 1
5 years 9 months ago #29532215
by RickBrooks
Replied by RickBrooks on topic SDC2160S Pulse Width Input
Have you come up with a firmware update for my single channel controller running in Pulse Width mode?
Rick
Rick
Please Log in or Create an account to join the conversation.
5 years 9 months ago - 5 years 9 months ago #29532217
by blake
Rick please accept my apologies for the late reply. Please find the attached firmware for the single channel SDC. Let me know if you need anything else.
Replied by blake on topic SDC2160S Pulse Width Input
Rick please accept my apologies for the late reply. Please find the attached firmware for the single channel SDC. Let me know if you need anything else.
Please Log in or Create an account to join the conversation.
- RickBrooks
- Topic Author
- Offline
Less
More
- Posts: 9
- Thank you received: 1
5 years 9 months ago #29532220
by RickBrooks
Replied by RickBrooks on topic SDC2160S Pulse Width Input
Blake,
That worked perfectly.
Thanks,
Rick
That worked perfectly.
Thanks,
Rick
The following user(s) said Thank You: blake
Please Log in or Create an account to join the conversation.
Moderators: tonysantoni
Time to create page: 0.095 seconds