AX2500 Controller Help
- Clayton
- Topic Author
18 years 2 months ago #5324789
by Clayton
AX2500 Controller Help was created by Clayton
<P style="MARGIN: 0px">Lets try this again,<BR><BR>Does anyone know where I can find the firmware version 1.3 for the AX2500 controller? Also, will the RoboRun v1.7 work with that firmware version?<BR><BR>Thanks,<BR>Clayton
Please Log in or Create an account to join the conversation.
- cosma
18 years 2 months ago #5327368
by cosma
The file is at <A href="dev.roboteq.com/dev1/download/roboup13-082503.zip" target=_blank>www.roboteq.com/download/roboup13-082503.zip
Replied by cosma on topic Re:AX2500 Controller Help
The file is at <A href="dev.roboteq.com/dev1/download/roboup13-082503.zip" target=_blank>www.roboteq.com/download/roboup13-082503.zip
Please Log in or Create an account to join the conversation.
- Clayton
- Topic Author
18 years 2 months ago #5333704
by Clayton
Replied by Clayton on topic Re:AX2500 Controller Help
<P style="MARGIN: 0px">Is that firmware version for the 2500 or the 2550, because I can not get it to work. If it is for the 2500 then I must be doing something wrong still, because I can not get it to save to the controller still. <BR><BR>Thanks,
<P style="MARGIN: 0px">Clayton
<P style="MARGIN: 0px">Clayton
Please Log in or Create an account to join the conversation.
- cosma
18 years 2 months ago #5350522
by cosma
V1.3 works for both the AX2500 and the AX2550. Please report where you are having difficulties: Cannot update the software, or the controller does not properly works with the new software.
Replied by cosma on topic Re:AX2500 Controller Help
V1.3 works for both the AX2500 and the AX2550. Please report where you are having difficulties: Cannot update the software, or the controller does not properly works with the new software.
Please Log in or Create an account to join the conversation.
- Clayton
- Topic Author
18 years 2 months ago #5363991
by Clayton
Replied by Clayton on topic Re:AX2500 Controller Help
<P style="MARGIN: 0px">I got the firmware to update, but am unable to communicate through rs232 using the hyper terminal. When I connect to the controller, I dont get a the message that the manual says you should get, all that I get is a repeating W, ie WWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWW<BR>WWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWWW, etc.<BR><BR>When I try using RC to move the motor forward/reverse, I only get the forward signal, but no motor movement.<BR><BR>Any thoughts?<BR><BR>Thanks, <BR>Clayton
Please Log in or Create an account to join the conversation.
- cosma
18 years 2 months ago #5371948
by cosma
Replied by cosma on topic Re:AX2500 Controller Help
<P style="MARGIN: 0px">If you get W's every second, this means that the controller is in RS232 mode with the watchdog enabled.
<P style="MARGIN: 0px">
<P style="MARGIN: 0px">If this happens after you uploaded the new software, this may be because you have not reset or powered down/up the controller prior to launching hyperterm.
<P style="MARGIN: 0px">
<P style="MARGIN: 0px">After resetting, you should read "no ctrl" on the display, indicating that the controller is in RC mode, waiting for a signal. When a valid RC signal is present, the "no ctrl" message disappears and you should be able to controll the motors.
<P style="MARGIN: 0px">
<P style="MARGIN: 0px">If this happens after you uploaded the new software, this may be because you have not reset or powered down/up the controller prior to launching hyperterm.
<P style="MARGIN: 0px">
<P style="MARGIN: 0px">After resetting, you should read "no ctrl" on the display, indicating that the controller is in RC mode, waiting for a signal. When a valid RC signal is present, the "no ctrl" message disappears and you should be able to controll the motors.
Please Log in or Create an account to join the conversation.
- Clayton
- Topic Author
18 years 1 month ago #5442238
by Clayton
Replied by Clayton on topic Re:AX2500 Controller Help
<P style="MARGIN: 0px">Ok...I have gotten the software and firmware versions to work, but now am unable to get the motors to operate on either channel in either direction. I am trying to control them using the hyperterm interface. The controller is getting the command(I can see that it is because the 7 segment display is changing, and I an getting a "+" after I send the command). Any help would be great!<BR><BR>Thanks, <BR>Clayton
Please Log in or Create an account to join the conversation.
- cosma
18 years 1 month ago #5444663
by cosma
We will call you to help you directly.
Replied by cosma on topic Re:AX2500 Controller Help
We will call you to help you directly.
Please Log in or Create an account to join the conversation.
Moderators: tonysantoni
Time to create page: 0.068 seconds