- Forum
- Roboteq Motor Controllers
- General Issues
- 16CH Wireless Wired Servo Controller Control Board + 200M Wireless Module
16CH Wireless Wired Servo Controller Control Board + 200M Wireless Module
6 years 9 months ago #29532216
by Boily
Hi, I am using an SDC2130S controller, I upgraded the firmware to v1.6 and robotrun to v1.6
The controller works fine with the receiver Spectrum AR6100E (6 channels). I can see the signal on the Pulse In input.
If I connect a 16CH Wireless Wired Servo Controller Control Board + 200M Wireless Module, there in no signal on the Pulse In input. I checked with a Scope and the signal is present. This 16ch wireless Controller works fine with different Standard Servo.
The only difference is the repeat rate (it's higher on this controller).
Is there an issue with the repeat rate (10 ms, 15 ms, 20 ms)
The controller works fine with the receiver Spectrum AR6100E (6 channels). I can see the signal on the Pulse In input.
If I connect a 16CH Wireless Wired Servo Controller Control Board + 200M Wireless Module, there in no signal on the Pulse In input. I checked with a Scope and the signal is present. This 16ch wireless Controller works fine with different Standard Servo.
The only difference is the repeat rate (it's higher on this controller).
Is there an issue with the repeat rate (10 ms, 15 ms, 20 ms)
Please Log in or Create an account to join the conversation.
6 years 9 months ago #29532218
by blake
Replied by blake on topic 16CH Wireless Wired Servo Controller Control Board + 200M Wireless Module
Please Log in or Create an account to join the conversation.
6 years 9 months ago #29532219
by Boily
Replied by Boily on topic 16CH Wireless Wired Servo Controller Control Board + 200M Wireless Module
I uploaded the firmware and I got the same issue.
Pulse In is always 0. We can see some activity on Din1 and the Led Pulse is not lit.
Pulse In is always 0. We can see some activity on Din1 and the Led Pulse is not lit.
Please Log in or Create an account to join the conversation.
6 years 9 months ago #29532221
by blake
Replied by blake on topic 16CH Wireless Wired Servo Controller Control Board + 200M Wireless Module
Because you confirmed that the pulse inputs work with the spectrum receiver we know the hardware is okay. As long as your servo control board specs are within the limits detailed on the
SDC2130S Datasheet
(Table 7), it should work as well. Have you compared specs?
Please Log in or Create an account to join the conversation.
6 years 9 months ago #29532222
by Boily
Replied by Boily on topic 16CH Wireless Wired Servo Controller Control Board + 200M Wireless Module
The Pulse repeat rate is 50-250 for the SDC2130S
It's 125 for the AR6100E (works)
and 72 for my 16 channel wireless controller, so it should works... (do not work)
It's 125 for the AR6100E (works)
and 72 for my 16 channel wireless controller, so it should works... (do not work)
Please Log in or Create an account to join the conversation.
6 years 9 months ago #29532223
by blake
Replied by blake on topic 16CH Wireless Wired Servo Controller Control Board + 200M Wireless Module
Please send your controllers configuration file along with the datasheet or make/model of the controller board to This email address is being protected from spambots. You need JavaScript enabled to view it. so that we may take a closer look
Please Log in or Create an account to join the conversation.
Moderators: tonysantoni
- Forum
- Roboteq Motor Controllers
- General Issues
- 16CH Wireless Wired Servo Controller Control Board + 200M Wireless Module
Time to create page: 0.097 seconds
